English
简体中文
ไทย
繁體中文
日本語
한국어
Sensor Systems
SNT-CSM 103 / 106 / 110
ModelsSNT-CSM 103 / 106 / 110Torque/Angle Transducer Servo Screwdriver. Refer to the specifications below to select the exact model.
Technical documents4 filesPrice and lead time are confirmed by model, quantity and project requirements.
Local selection supportAccessory & controller matchingManufacturer documents
PRODUCT INFORMATION
Features & technical specifications
Features
● Compact and ergonomic design for long time operation without hand fatigue
● Rubberized grip provides a non-slip surface to secure hold, absorbs shock and vibration
● Tool start methods: lever start, external start
● 4 LED illumination mode: On / Off / On when the tool starts / On when triggered
● Tightening status LED and buzzer alert
● Transducerized DC torque & angle control tightening system
● High-resolution encoder, angle control 1° - 30600° (30600° is approx. 85 turns)
● < 1% tolerance, precision & accurate torque transducer
● Beginner-friendly downshift and threshold settings in normal mode
● 5 available rundown steps to customize your screw rundown process
Select SNT-CSM103, SNT-CSM106 or SNT-CSM110 by the correct torque unit
The manufacturer table lists torque in kgf.cm: SNT-CSM103 0.375–3; SNT-CSM106 0.75–6; SNT-CSM110 1.25–10. Its N.m and lbf.in cells are marked “-”. Do not read those kgf.cm numbers as N.m. No-load speed ranges are 20–1600, 20–1200 and 20–800 rpm respectively.
Supplied configuration and confirmation
All three rows list DC 40 V, 40 W, 465 g, 210 mm and KL-NTCS-M7. The repeatability statement is retained as “+/- 3sigma / AVG., 5%”; do not replace it with a different sensor accuracy claim. Listed bit codes are B9.5, C, C-HM, D; confirm the drawing, holder and supplied configuration.
Questions before ordering
Are the published torque figures N.m?
No. The ranges 0.375–3, 0.75–6 and 1.25–10 are under kgf.cm. The manufacturer leaves N.m and lbf.in blank with a dash. Confirm the required unit and application target before ordering.
Which model should I choose?
Select by the exact torque range and required process speed, then validate on the screw joint. The 103/106/110 speed ranges differ; the model number alone is not a torque unit or a promised application result.
Which controller and bits should I request?
The table lists KL-NTCS-M7 and bit codes B9.5, C, C-HM, D. Quote the tool, controller, matching cables, holder and required bit as confirmed line items; do not assume all accessories are included.
How should I specify a hard or soft joint?
Provide screw size/type, material, target torque and angle, required speed/steps, workstation layout, quantity and receiving date. Engineering must confirm the application; the public table does not give separate hard/soft torque ranges.
Quotation, stock confirmation, PO delivery estimate and inquiry checklist
Specifications
Model | Input voltage | Torque (N.m) | Torque (kgf.cm) | Torque (Lbf.in) | Repeatable Torque Accuracy | Free Speed (r.p.m)
| Power Consumption | Weight (g) | Length (mm) | Applicable controller | Bit Type |
SNT-CSM103 | DC40 | - | 0.375~3 | - | +/- 3sigma / AVG., 5% | 1600~20 | 40W | 465 | 210 | KL-NTCS-M7 | B 9.5、 C、 C-HM、 D |
SNT-CSM106 | DC40 | - | 0.75~6 | - | +/- 3sigma / AVG., 5% | 1200~20 | 40W | 465 | 210 | KL-NTCS-M7 | B 9.5、 C、 C-HM、 D |
SNT-CSM110 | DC40 | - | 1.25~10 | - | +/- 3sigma / AVG., 5% | 800~20 | 40W | 465 | 210 | KL-NTCS-M7 | B 9.5、 C、 C-HM、 D |
Configuration, measurement and quotation
All three rows list DC 40 V, 40 W, 465 g, 210 mm and controller KL-NTCS-M7. Listed bit codes are B 9.5, C, C-HM and D. The related accessory is KH-1L. Confirm the exact holder drawing, screwdriver revision, cable, mounting and supplied-item list; the code list does not establish every bit/holder combination or that accessories are included.
The published start methods are lever start and external start. The features describe an encoder angle-control range of 1°–30600° and five programmable rundown steps. This is not a stated angle accuracy, and external start does not specify pinout, voltage or PLC compatibility. Require the approved wiring and integration instructions for the actual controller/tool pair.
The feature claim “less than 1%” for the transducer differs from the table note “+/- 3sigma / AVG., 5%” for repeatability. Keep these statements separate; do not turn either into a guaranteed joint accuracy. Confirm torque unit, measurement/calibration conditions, joint behaviour and acceptance criteria. Production records require the configured controller and verified data fields; counting alone is not measured torque/angle evidence.
Is SNT-CSM110 rated to 10 N·m?
Not according to this table. Its upper entry is 10 kgf·cm and the N·m cell is a dash. Confirm the application torque and unit before model selection.
Can it run directly from AC power or KL-TCC?
The tool table specifies DC 40 V and KL-NTCS-M7. Do not connect it directly to AC or assume another controller is interchangeable.
What should I specify for a model quotation?
Choose SNT-CSM103, SNT-CSM106 or SNT-CSM110 explicitly. Provide torque/unit, screw/joint, required speed and angle steps, controller/cable/bit/fixture, record requirements, quantity, delivery location and required date. Price, stock and supplied items require sales confirmation.
※Please move table left and right to read contents.
Applicable Bit Type
Dimensions
Compatible Accessories
KL-NTCS-M7 Series
Manufacturer Downloads
Confirm the exact model, compatible components, manual version and availability with KILEWS Thailand before ordering or installation.
DOCUMENTS
Product documents
RELATED PRODUCTS
Related models & accessories
